An 8 bolt segment broom is replaced by our 4 bolt mount broom. Our brooms have half the fasteners of segmented brooms. Plastic-back brooms, with the mounting nut in the plastic, can spin requiring a torch to remove the bolt. Mounting nuts are easily accessible on top of the spinner and not exposed to elements that would corrode the threads. Do not tighten the nut.Ĩ)Secure all nuts to a minimum of 50 foot pounds of torque or until they are tight. Do not tighten the nut.Ħ)Raise the opposite side of the broom and start a nut and washer. Below are instructions to mount a Whart Hog.Īfter your segmented broom has been removed, proceed as follows:ġ)Leave the spinner out and in the down or sweep position.Ģ)Slide our broom under the spinner (with spacers on).ģ)Align a bolt with the hole that is facing towards the front of the machine.Ĥ)Let the spinner drop down so the bolt comes up through the mounting hole.ĥ)Start your nut and washer. Our brooms are very easy to mount or dismount on your machine compared to segmented brooms. How easy is it to mount and dismount your brooms on the machine? This will help to keep your pickup head from impacting curbing or obstacles when cornering. YES !! The larger broom foot diameter of Whart Hog brooms will stand your sweeper farther off curbing and obstacles. Will your broom help stop pick up head impact when cornering? In addition, the brush wire is splayed at the ends to give you the ability to reach further into the curb. The additional wire angle gets the brush wire deeper into the curb for better sweep capability. Our Whart Hog brooms will help solve this problem. How will your broom help with compacted dirt in curbing? The four inch increase in broom foot diameter will help to stand the sweeper an additional two inches off the curbing. A standard 36 inch broom replaced by our broom will have a 40 inch foot diameter. The design of our brooms increases the foot diameter of the broom. Our Whart Hog brooms will help stop this problem. I have a problem with being to close to the curb when cornering? Also, the increased angle of the wire allows the brush to have more flair for a better foot print. The additional wire angle requires less down-force to achieve sweep, and flick to get the dirt to your pickup head. The wire is set in the backer at a 35 degree angle instead of the 20 degree angle of standard brooms. Whart Hog brooms have a higher degree of sweep capability compared to industry standard brooms. Our brooms are easier, faster and safer for the operator/mechanic to change, saving you time and money. This is due to the increased wire pitch angle to 35 degrees. The value lies in the fact that our brooms are achieving up to 150 hours of sweep time. What is the value in using a steel-backed broom? Also, Whart Hog Brooms are the only fully recyclable broom made and should be recycled not disposed of in the Land Fill. Plastic or plywood backs can shatter upon impact thus requiring the broom to be changed. If our broom is impacted and bent, it can be straightened and you can continue to use the broom. manufactures the steel-backed broom for its strength and durability. Why use a steel-backed broom verses a plastic-backed broom? You can see below that Whart Hog Brooms have a greater sweep time average than segmented brooms.ģ0″ Standard Whart Hog broom averages 120 hours sweep timeģ0” Super Whart Hog broomaverages170 hours sweep time.ģ6″ Standard Whart Hog broom averages 150 hours sweep time.ģ6” Super Whart Hog broom averages 200+ hours sweep time.Ĥ4″ Standard Whart Hog Broom averages 150 hours sweep time.Ĥ4” Super Whart Hog broom averages 200+ hours sweep time. How many hours are your brooms achieving in curb and gutter sweeping?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |